admin 17 November, 2018 0

ADC0808 PDF

The ADC IC is a commonly used ADC module for projects were an external ADC is required. Find ADC pin diagram, features & datasheet. ADC – A/D converters, used to convert analog signal to digital signals, like ADC IC, ADC IC, pin configurations and interfacing with microcontroller . The ADC/ADC is an 8 bit ADC that also contains an 8 channel multiplexer. The FPGA used in this case was the Altera 10k20RC that is found on.

Author: Vudozahn Turan
Country: Panama
Language: English (Spanish)
Genre: Environment
Published (Last): 14 February 2018
Pages: 217
PDF File Size: 9.33 Mb
ePub File Size: 10.49 Mb
ISBN: 434-1-33689-173-8
Downloads: 32017
Price: Free* [*Free Regsitration Required]
Uploader: Kazikasa

Access Denied

Step size is the change in analog input to cause a unit change in the output of ADC. The voltage level that, when received as an input, will output “” to the FPGA. These three bits have to be set as shown in the qdc0808 below to access the respective analog channel. Analog Channel 1 to 5.

Complete Technical Details can be found at the datasheet give at the end of this page. The ADC stores the data in a tri-state avc0808 latch until the next conversion is started, but the afc0808 is only output when enabled. The source resistance must be below 10kohms for operation below kHz and below 5kohms for operation around 1.

It is recomended that the source resistance not exceed 5kohms for operation at 1.

ADC is the Analog to Digital converterwhich xdc0808 analog data into digital format; usually it is used to convert analog voltage into digital format. Skip to main content.

ADC IC Datasheet | ADC Pin Configuration

Atmospheric Vortex Engine Twister Power. The step size is decided qdc0808 on set reference value. On the rising edge of the pulse the internal registers are cleared and on the falling edge of the pulse the conversion is initiated. As you can see in the image the voltage value is 2. The minimum pulse width is ns. Once loaded the multiplexer sends the appropriate channel to the converter on the chip. Or even to use as a standalone ADC module. Its resolution is 8 so it can encode the analog data into one of the levels 2 8.

Digital output bit 4.

I have changed some modifications too but still its not working. The default step size is Since the ADC IC can measure up to eight Analog voltage and also does not have an internal clock slightly requires more components to adx0808 it work compared to its predecessor ADC Clock The clock signal is required to cycle through the comparator stages to do the conversion. Actually the code u have posted is not working i guess due to the initialization i think.

A, B, and Aec0808. It goes low when a conversion is started and high at the end of a conversion. C is the most significant bit and A is the least. And data pin D4-D7 is connected to pins P2. Arc0808 means it must remain stable for up to 72 clock cycles. The ADC needs some specific control signals for its operations like start conversion and bring data to output pins. The start signal should conform to the same range as all other control signals.

ADC Technical Data

These 7 pins are the input pins for Analog voltage sensor. Start conversion; input pin; a low to high pulse is given. Input pin; a low to high pulse brings data to output pins from the internal registers at end of conversion.

The input which is to be converted to digital form can be selected by using three address lines. As with all control signals it is required to have an input value of Vcc – 1. This means that in order adc808 get it to work, there is a total of seven control signals that must be sent from the FPGA. The following control signals are used to control the conversion. Qdc0808 Lines Because the chip has an 8 channel multiplexer there are three address select lines: That is because ADCs require adc080 and can contain control logic including comparators and registers.

The obtained value is 2. I have not tested on the actual hardware but i have done the simulation in proteus and it adc8008. These three pins are used to select the channel.

For a quick reference refer to table 2. And show on LCD as name Ch2. The signal can be tie to the ALE signal when the clock frequency is below kHz. I have made small changes to the original code.

8051 – ADC0808 Interfacing

All of the signals are explained below. Vref is connected to ground normally.

Powers the IC typically with 5V. This device has three channel address line namely: Quote and Order boards in minutes on https: Clock input; to provide external clock. Table 2 provides a summary of all of the input and output to the chip.

We can provide it by using oscillator or by using microcontroller.